supply chain transparency

List of the contents of this article:

• 1,supply chain transparency How to fix the setting protection of the computer system?
• 2, How to turn on System protection<
• 3, How to solve the problem of air conditioning display system protection
• 4, How to turn on/off system protection in win10 system
• 5, The computer protection system is turned off. How to turn it on?

How to fix the setting protection of the computer system?

1. If there is a problem with the computer system, the following are some common repair steps to restart the computer. Usually, after the computer has a problem, the first step is to try to restart the computer. This will clear temporary files and reset system settings, and sometimes solve small problems. System restore If the problem persists after restarting the computer, you can try to restore the system.

2. Check whether there is a write protection switch. Some storage devices (such as USB flash drives and SD cards) will be equipped with write protection switches, which need to be turned on to write data. Cancel the read-only attribute. Some files or folders may be set to read-only attributes, and you need to cancel the read-only attribute before you can write. Format the storage device.

3. This article will introduce a computer system repair method to help readers solve computer system problems. Enter the BIOS setting interface to start the computer. When the Press Del to Enter BIOS Setup prompt is displayed on the screen, press the Del key to enter the motherboard BIOS setting interface.

4. Click "System Restore" in the "System Protection" interface just now.Click Next in the pop-up system restore prompt window. Click to show more restore points, and you can also see the restore points automatically created by the system after the update.

5. Question 1: How to fix a problem with the computer system? Simple problems can be repaired with small software such as Jinshan Guardian and system DIY. If there is a big problem, you need to check or redo the system to solve it. Question 2: How to repair the system of the computer host? Restart the computer without entering the system. Hold down the F8 key before and select the last correct configuration to try.

How to turn on system protection

Opening method: computer right-click menu properties---system protection. Select System Protection---Create System Restore Point---Configure Select Restore System Settings and Previous Versions of Files---OK.Open the Start menu and click Settings. Click "Update and Security". Click "WindowsDefender".

Opening method: computer right-click menu properties---system protection. Select System Protection---Create System Restore Point---Configure Select Restore System Settings and Previous Versions of Files---OK.

First of all, open the [Computer] window, and then click the [Open Control Panel] option according to the arrow in the figure below. The second step is in the [Control Panel] window, click the [System] option according to the arrow in the figure below.

Click the "Start" button, and then select "Control Panel". In the control panel window, select the "Security Center" option. In the security center window, you can see the security status of the computer.If the security center detects that some items are not turned on, a warning message will be displayed.

How to solve the air conditioner display system protection

1. Solution: Replace the compressor overheating protection Instrument. Problems with the compressor itself, cylinder, coil burnt, etc. Solution: Replace the compressor.Snow seed problems, excessive or insufficient overheating protection of the compressor during long-term operation. Solution: Check the pressure value of the snow seed and control it to the normal range.

2. Clean the air conditioner regularly: If the air conditioner is not cleaned for a long time, it is easy to cause dust and bacteria to accumulate inside the air conditioner, causing damage to the circuit board and other parts, resulting in the inability of the air conditioner to operate normally. Therefore, it is very important to clean the air conditioner regularly, which can increase its service life and stability.

3. First of all, we can try to turn off the air conditioner and wait for a period of time for it to cool down. If the problem persists, we should check whether the circuit is short-circuited or faulty. In addition, we can also check whether the power supply of the air conditioner is stable and whether the installed fuse is normal.

4. The solution is to adjust the temperature to avoid being too low.During the ventilation process: During the ventilation process, the air conditioner will also enter a protected state. At this time, it should wait until the ventilation is completed before using it. Unstable power supply: When the power supply is unstable, the air conditioner will also enter the protected state. At this time, it is necessary to check whether the power supply is normal.

5. Check the controllers and sensors of the air conditioning system: faulty controllers or sensors may also cause low-voltage protection triggers. Check and repair the faulty parts. Seek professional help: If none of the above methods can solve the problem, it is recommended to seek professional air conditioner maintenance personnel to diagnose and repair the problem.

6. If your central air conditioner has a protective shutdown, you can try the following methods: check the power supply: whether the fuse is broken, whether the plug is loose, etc., to ensure that the central air conditioner is connected to a stable and reliable power supply.

How to turn on/off system protection in win10

In the first step, right-click the computer or this computer icon. Step two, after coming to the pop-up window shown in the figure below, click the property option in the red box. Step three, in the property page shown in the figure below, click the advanced system setting option indicated by the arrow.

On the Windows 10 desktop, right-click the "This Computer" icon on the desktop and select the "Properties" menu item in the pop-up menu. At this time, the system properties window will open. In the window, we click the shortcut link of "Advanced System Settings" on the left sidebar.

Method/Step 2 First, press [Ctrl+Shift+Esc] shortcut key to open [Task Manager], and then click [Service] first according to the arrow in the figure below, and then right-click the [WinDefend] option. The second step is in the pop-up menu bar, click the [Stop] option according to the arrow in the figure below.

Next, I will share with you the specific method of turning off the system file protection function under Windows 10.

The details are as follows: First, the first step is to right-click the [This Computer] icon, and click the [Properties] option in the pop-up menu bar according to the arrow in the figure below. Step 2 After opening the [Properties] window, click the [System Protection] option according to the arrow in the figure below.

First, open My Computer and click My Computer Properties in it.Secondly, select the advanced system settings and find the system protection in it. Finally, click System Restore, then click the recommended restore or the restored point created by yourself, and click OK to cancel.

The computer protection system is turned off. How to turn it on?

Right-click on this computer on the desktop (win7 is called this computer) and select properties in the pop-up menu. After entering the properties page, click Advanced System Settings. Click the system protection option in the open interface. As shown in the figure, click the disk symbol to be protected, and then click to configure.

Click the "Start" button, and then select "Control Panel". In the control panel window, select the "Security Center" option. In the security center window, you can see the security status of the computer.If the security center detects that some items are not turned on, a warning message will be displayed.

First of all, open the [Computer] window, and then click the [Open Control Panel] option according to the arrow in the figure below. The second step is in the [Control Panel] window, click the [System] option according to the arrow in the figure below.

Method 1 Turn on the computer, select "Computer" on the desktop with the mouse, then right-click and select "Properties", select "Advanced System Settings" on the left of the window, select "System Protection", and select the c disk, that is, the system disk, under the available drive.

The restoration method is: Win7 or 8 to restore the system, right-click the computer to select properties, select system protection on the right, system restore, and follow the steps. 2) Win7 system alsoYou can use the backup image function to open the control panel/system and security/backup and restore/select to create a system image on the left/follow the steps and requirements.