Timber (HS code ) import patterns

List of catalogs of this article:

• 1,Timber (HS code ) import patterns How does the car start
• 2, How to start the car
• 3, What are the steps to start the car?
• 4, How to start a motor vehicle
• 5, How to start a car

How does the car start

1. Question 4: How does the car start? Insert the key, turn one grid clockwise, turn on the power, wait for about 6-10 seconds, and then put down the clutch pedal and turn the key clockwise. Key, start the car, release the key, then release the clutch pedal, warm up the engine for 1-3 minutes, best, put down the clutch pedal, hang up the gear, and start.

2. Ignition switch Ignition switch is the last step of starting the car. When operating, the ignition switch should be set to the "start" position. Because the position of the ignition switch is generally high, pay attention to accuracy when operating, otherwise accidents may occur.

3. Need to insert the key to hang on PGear, step on the brake pedal, unstw the key to start the engine. If the gear is not in p gear or do not step on the brake pedal, you cannot start the engine. 3 If it is a manual transmission car, you don't need to step on the brake pedal when starting the engine. You need to step on the clutch pedal to the end, and then start the engine.

How to start the car

You need to insert the key to the P gear, step on the brake pedal, and unsew the key to start the engine. If the gear is not in the p gear or does not step on the brake pedal, the engine cannot be started. 3 If it is a manual transmission The car does not need to step on the brake pedal when starting the engine. You need to step on the clutch pedal to the end and then start the engine.

Pay attention to starting the car: Look: Before starting the car, you need to checkCheck the parking position, whether there are oil stains and water stains, whether the front and rear lights are damaged, and whether the tire pressure is normal. Check that there is no mistake before getting on the bus. Inspection: Engine oil, antifreeze, signal lights and other parts need to be checked.

Starting a car is the first step in driving, and it is also one of the most familiar operations for many people. Before starting the car, you need to check whether the vehicle is in a normal state, insert the key, ignition, hang the gear, refuel door, release the clutch, and finally start the car. As long as you follow the correct steps, you can easily start the car and start driving.

What are the steps to start the car?

Check around the vehicle before getting on the car to make sure that there are no small animals or children next to you, or whether there are iron nails, glass and other items that hinder the safety of the car. The first thing to do when entering the car is to fasten your seat belt. The brake on the left and the accelerator on the right. This order must be remembered clearly.

After starting, the gear is put in D gear, slowly release the brake, and the vehicle will move forward. If it is a manual transmission, you need to step on the clutch and start the engine, then hang it into 1st gear, slowly release the clutch, move the right foot from the brake pedal to the accelerator pedal, and refuel slightly.The throttle and clutch are used together, and the vehicle moves forward slowly.

Steps to start the car correctly: adjust the seat to your position after getting on, and then fasten your seat belt. Start the car, then step on the clutch with your left foot and hang the first gear. Turn on the left turn signal and honk the horn.

The gear should be placed in the P or N position (if it is in another position, the automatic gear car cannot be ignited). Dial the key to the ON position first and stay for about 10 seconds (circuit self-checking process, check whether the indicator lights on the dashboard are displayed normally). If the self-check is normal, it can be ignited and started.

How to start the motor vehicle

1. The correct way to start the engineYes: When starting, turn the ignition key to the on position, wait for 58s, and then turn the key to the start position to start the engine.

2. Fasten your seat belt in the car and insert the key into the keyhole. Rotate the key until the acc stops and wait for about 2-3 seconds to make the main power relay contact firmly, so that the device that needs to be energized in the first part can be energized.

3. Before starting, you should turn on the ignition switch and wait for about 5 seconds for the oil pump to work before starting. It is best to turn on the lights, radios and other electrical equipment after starting the engine. Before parking, turn off these electrical appliances that consume electricity and then turn off the engine. 2 Some drivers, in winter The season starts the car and doesn't work.

4. Before starting the engine, the following preparations should be made: (1) Check the plane of the engine lubricant and coolant.(2) Check whether each high-voltage line is loose (gasoline engine).

5. Starting the car engine with ignition is the first step of driving. If the starting method is incorrect, it will have a great impact on the life of the battery and the starter. Let's learn the correct way to start the engine: when starting, turn the ignition key to the on position and wait for 5? 8s, and then turn the key to the start position to start the engine.

How to start the car

Do not twist the key in the Lock position, wait for about 2 seconds, and then you can directly stop at the ON position through the ACC position and wait for about 5 seconds.

Check whether the battery meets the requirements. If the battery is too low, then it can't be ignited normally. At this time, you need to use a battery charger to charge it. When the battery meets the normal requirements, it can be ignited.

Before starting, make sure that the gear of the car is in idal gear, then step on the clutch, first turn the key to ACC gear, stay for about 3 to 5 seconds, let the car circuit carry out system self-check, and then turn to START gear to start after normal. After the startup is completed, you must release the key and let the key return to the ON gear.

Continue to turn the key to on (if the key can't be turned, it is likely that the steering wheel is locked. While gently turning the steering wheel, just turn it), and then stop waiting for 6-10 seconds to let the oil pump relay absorb. Start the engine, and then observe whether the indicator light of the instrument is normal.

CorrectThe ignition method of the car is: step on the clutch deeply, turn the ignition key to the ON position, wait for 5 to 8 seconds, and then turn the key to the starting position to start the engine; once the engine starts smoothly, the ignition key should be released immediately to automatically return to the ON position.

The specific operation steps for starting a car are as follows: Required tools: a car with good performance. Step on the brake pedal of the car. Press the one-button start button of the car. The car instrument lights up and the vehicle starts. Step on the car clutch pedal. Put the car on the first gear.