Real-time shipment inspection data

List of the catalog of this article:

• 1, How often should the cylinder head gasket be replaced?
• 2
  、What is the material of the Audi engine gasket
• 3, Single-layer iron cylinder cushion and multi-layer distinction
• 4  、 Why is the round cushion of the engine exhaust pipe interface easy to burn and how to prevent it?

How often should the cylinder head gasket be replaced?

1. The cylinder head gasket should be replaced every three years. Damage to the valve cover pad will cause engine oil leakage, resulting in poor engine airtightness, affecting the normal operation of the engine, and even causing the engine to be scrapped in serious cases. The valve cover gasket is damaged and needs to be replaced in time. The symptoms of cylinder pad damage are as follows: 1.

2. The service life of the cylinder head pad is generally replaced once every two years: the cylinder head pad, abbreviated as the cylinder pad (commonly known as the cylinder bed), is an elastic sealing element placed between the cylinder body and the cylinder head.

3. As long as the cylinder head is not damaged or deformed, it does not need to be replaced. The use of the cylinder head cushion generally needs to be replaced once every two years.

4. The time to replace the cylinder pad of the car is not certain, and it needs to be analyzed according to the specific situation. Some car cylinder pads only take half an hour to replace, some take half a day, and some take a day to replace the cylinder pad because the engine needs to be disassembled.

5. The time for changing the cylinder cushion of the car needs to be analyzed specifically, generally half an hour. The rest is because it takes a day to disassemble the engine.

6. It must be replaced in time, so as to better ensure that the cylinder seal does not leak air, and keep the coolant and oil flowing from the body to the cylinder head from leaking, so as to better extend the service life of our cars.

What is the material of the Audi engine gasket

1. The gasket is mostly made of rubber. Because the service life of the vehicle is too long, the rubber material will age and harden, causing oil leakage.

2. Asbestos rubber material. XB350 gasket is a sealing gasket material made of asbestos and rubber as the main raw materials. It is suitable for the highest temperature of 350 degrees Celsius, and it is made by glueing, weaving, pressing, vulcanization and other processes.

3. The general sealant gasket is made of natural rubber and has a long service life. In addition to some types of rubber, some are made of metal or non-metal, such as stainless steel or aluminum, and some are copper.

4. The sealing gasket is made of metal or non-metallic plate material by cutting, stamping or cutting and other processes. It is used for the sealing connection between pipes and the sealing connection between the parts of machinery and equipment and the machine parts.

5. The engine piston and the cylinder block are sealed by a piston ring. According to the material, there are mainly two types of alloy cast iron and steel, as well as a very small amount of metal ceramics and polytetrafluoroethylene. The piston ring is used between the piston and the inner wall of the cylinder to ensure no air leakage.

6. LaunchThe cylinder pad is made of two materials, one is a metal asbestos pad made of asbestos, and the other is a metal pad made of a single piece of polished steel plate. There is an elastic ridge at the seal, which is sealed with the elasticity of the ridge and the effect of heat-resistant sealant. Metal pads are widely used, and various technical indicators exceed those of asbestos cylinder pads.

Single-layer iron cylinder cushion and multi-layer difference

Pasat b5 cylinder cushion cotton is good. The screws of the asbestos cushion cylinder head in the Pashat b5 cylinder are tight and high temperature resistant. The iron cylinder pad is not tight, and it is easy to leak water and air.

Cylinder pad rubber material: At present, the main types of automotive cylinder pad materials used in China are as follows: asbestos gasket-free, mainly made of paper and its composite board (paper products), with poor sealing and low temperature resistance.

Please note that the 3-cylinder valve is relatively damp and the color is different from that of 1-2-4 cylinder. 3-cylinder valve. Check the cylinder pad, please pay attention to the red circle mark of the 3 cylinders. 3 The cylinder cushion is broken, and there is a waterway above the break. The iron cylinder cushion is divided into upper and lower layers, and the lower layer is just disconnected from the sealed part of the cylinder.

Iron is good. High temperature resistance: iron is resistant to high temperature and not easy to deform, and asbestos is easy to deform, not resistant to high temperature, and has poor sealing. Strong and durable: iron is stronger, used for a long time, and not easy to break, asbestos is easy to break, and the use time is short, so Lifan Maiwei 5 cylinder pad is better to use iron.

Why is the round cushion of the engine exhaust pipe interface easy to burn and how to prevent it?

1. The reason why the interface round pad is easy to cauterized: After the upper end of the mumper intake pipe is inserted into the inner end of the exhaust pipe interface, and then pressed with a protruding edge and fixed with two bolts.

2. The round pad of the engine exhaust pipe interface is the sealing gasket of the exhaust pipe. The reason why this sealing gasket is easily damaged may be caused by the excessive temperature of the exhaust. Therefore, to prevent this seal from being easily damaged, then we need to know the reason why the exhaust pipe is too high? I think there are nothing more than the following points.

3. According to the relevant information of the query, when the vehicle drives to the top of the slope, the engine temperature is relatively high, and the temperature of the exhaust gas is also very high, resulting in a high temperature transmitted to the exhaust pipe and other parts. At the beginning of the downhill, the exhaust brake is used, but at this time, due to the high temperature, the exhaust manifold cushion is It is easy to be burned.