1. If the width is too large, there will be no accident during overtaking or if the road marking is narrower than the width of the car, the state stipulates that the car The total width of the vehicle shall not exceed 5m to meet the needs of the use of relevant public roads.
2. However, as long as it meets the national standard "Dimensions, Axle Weight and Mass Limits of Road Vehicles" (GB1589-2004), they are all standard sizes.Measurement method of car size: length and number of times; width × height. As the name implies, the so-called length, width and height are the external dimensions of the car, usually in millimeters (mm).
3. Width is the distance between the most prominent points of the outer sheet metal of the body. The length data of a car is the distance from the front of the front to the end of the rear of the car. The width is the distance between the most prominent points of the outer sheet metal of the car body. Generally, the front wheel eyebrow position of the car is the widest, and the general reflector is not included in the width of the body.
4. According to the common rules in the industry, the width of the body does not include the width of the left and right rearview mirrors, that is, the width after the rearview mirror is folded. The height of the car body is defined as: the distance from the ground to the highest point of the car. The so-called highest point is the highest position on the top of the body, but does not include the length of the roof antenna.
5. Vehicle width: Vehicle width is the distance between the two planes parallel to the longitudinal symmetrical plane of the vehicle and facing the fixed protruding parts on both sides of the vehicle. The automatic measuring instrument of vehicle outline size should comply with the measurement regulations, and the maximum allowable error of the measuring instrument: 1% or 20mm.
6. The body size is the data of the length, width and height of the car, indicating the external size of the car body. Body length × width × height measurement standard: body length refers to the distance from the most prominent position at the front of the car to the most prominent position at the rear of the car.
Benchmarks In actual measurement work, the plane of the body corrector is generally taken as the height reference plane.
In the body knotIn structural maintenance, when measuring the body structure data with the body measurement system, there are three important dimensional reference benchmarks: reference surface, central surface and zero plane.
Therefore, the use of steel tape measure and gauge can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and production year should be correctly selected. Parameter comparison When selecting the measurement reference point, the following principles should usually be followed. 1 Confirm that the measurement reference point is not deformed.
The body width is defined as the distance between the two extreme points in the direction of the width of the car, that is, the distance between the most prominent positions on the left and right of the car body. According to the general rules of the industry, the body width does not include the extension width of the left and right rearview mirrors, that is, the width of the folding rearview mirrors. The body height is defined as the distance from the ground to the highest point of the car.
The quality of the whole vehicle equipment (kg): the quality of the car is fully equipped, including the quality of all equipment such as lubricating oil, fuel, accompanying tools, spare tires, etc. Maximum total mass (kg): the total mass when the car is fully loaded. Maximum loading mass (kg): the maximum loading mass when the car is driving on the road.
Therefore, the use of steel tape measure and gauge ruler can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and year of production should be correctly selected. ( 2) Parameter comparison: When comparing parameters, the following principles should generally be followed: ensure that the measurement reference point is not deformed.
1. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
2. You need a tape measure or laser rangefinder. If you choose to use a tape measure, make sure it is accurate and long enough to measure the length of the entire body. If you choose to use a laser rangefinder, follow the instructions to make sure that it has been calibrated and ready for use.
3. In order to accurately obtain the body data, the three steps are the measurement of the size, the measurement of the upper body size, and the measurement of the front size of the body. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. Measurement of the overall deformation of the car body: Body shaping positioning detection is to use the measurement system provided by the straightening system to measure the coordinate parameters of each measurement point on the body, and compare the measurement data with the standard data of the model to check the straightening quality.
5. Stop the car after driving 10km on the road with poor road conditions, and touch the shock absorber shell with your hand. If it is not hot enough, it means that there is no resistance inside the shock absorber and the shock absorber does not work.
The front bundle ruler can be used to check and measure the front bundle. The tested vehicle must ensure that the tire pressure, the wheel is not in the center, the steering mechanism and the wheel bearing adjustment are in good condition, and the front wheel must be in the center and straight. When measuring with a front ruler, park the car on a flat, dry and clean ground.
Measurement method of automobile front bundle: First of all, the measurement method of automobile wheel bearing clearance is adjusted, and the tire inflation pressure conforms to the regulations.
The adjustment and measurement of the front beam of the car are as follows: the front beam of the front wheel is to make the distance between the front end of the two front wheels of the car smaller than the distance of the rear end.The difference in distance is called the front beam value. Looking down from the top of the car, the left and right front wheels form an "eight" shape with an opening to the back; the front bundle of the front wheel can be adjusted by changing the length of the crossbar.
Checking the front bundle value is generally carried out on a special front wheel locator. The front beam measurement method is first of all to adjust the gap of the automobile wheel hub bearing, and the tire inflation pressure conforms to the regulations. Park the car on the horizontal road and drive in a straight line.
Therefore, when the current bundle value is inappropriate, it needs to be adjusted and measured. To measure the front beam of a car, it is generally necessary to use a special front wheel locator, and generally there is no such professional instrument for self-measurement, and it can only be measured through simple tools. Of course, there is a certain error in the front beam of the car measured in this way.
1. Car size detection is as follows: the body length is defined as the distance between the two extreme points of the car, that is, the distance between the two points from the most prominent position of the front bumper of the car to the most prominent position of the rear bumper.
2. Body size: First, we will measure the size of each part of the car body, including the length, width and height. These data are crucial to the design, manufacture and safety of vehicles. For example, if the body width exceeds the specified limit, the vehicle may not be able to drive on certain roads.
3. Measurement of size: In the body structure, most of the control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. When the freight vehicle passes through the off-site law enforcement monitoring point normally at a running speed range of 0.5-100km/h, the Shenbang outline size measurement ADM system can automatically complete the identification and measurement of the length, width and height profile size and wheelbase of the freight vehicle, and output the correct measurement results to Off-site law enforcement edge management server.
Medical reagents HS code verification-APP, download it now, new users will receive a novice gift pack.
1. If the width is too large, there will be no accident during overtaking or if the road marking is narrower than the width of the car, the state stipulates that the car The total width of the vehicle shall not exceed 5m to meet the needs of the use of relevant public roads.
2. However, as long as it meets the national standard "Dimensions, Axle Weight and Mass Limits of Road Vehicles" (GB1589-2004), they are all standard sizes.Measurement method of car size: length and number of times; width × height. As the name implies, the so-called length, width and height are the external dimensions of the car, usually in millimeters (mm).
3. Width is the distance between the most prominent points of the outer sheet metal of the body. The length data of a car is the distance from the front of the front to the end of the rear of the car. The width is the distance between the most prominent points of the outer sheet metal of the car body. Generally, the front wheel eyebrow position of the car is the widest, and the general reflector is not included in the width of the body.
4. According to the common rules in the industry, the width of the body does not include the width of the left and right rearview mirrors, that is, the width after the rearview mirror is folded. The height of the car body is defined as: the distance from the ground to the highest point of the car. The so-called highest point is the highest position on the top of the body, but does not include the length of the roof antenna.
5. Vehicle width: Vehicle width is the distance between the two planes parallel to the longitudinal symmetrical plane of the vehicle and facing the fixed protruding parts on both sides of the vehicle. The automatic measuring instrument of vehicle outline size should comply with the measurement regulations, and the maximum allowable error of the measuring instrument: 1% or 20mm.
6. The body size is the data of the length, width and height of the car, indicating the external size of the car body. Body length × width × height measurement standard: body length refers to the distance from the most prominent position at the front of the car to the most prominent position at the rear of the car.
Benchmarks In actual measurement work, the plane of the body corrector is generally taken as the height reference plane.
In the body knotIn structural maintenance, when measuring the body structure data with the body measurement system, there are three important dimensional reference benchmarks: reference surface, central surface and zero plane.
Therefore, the use of steel tape measure and gauge can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and production year should be correctly selected. Parameter comparison When selecting the measurement reference point, the following principles should usually be followed. 1 Confirm that the measurement reference point is not deformed.
The body width is defined as the distance between the two extreme points in the direction of the width of the car, that is, the distance between the most prominent positions on the left and right of the car body. According to the general rules of the industry, the body width does not include the extension width of the left and right rearview mirrors, that is, the width of the folding rearview mirrors. The body height is defined as the distance from the ground to the highest point of the car.
The quality of the whole vehicle equipment (kg): the quality of the car is fully equipped, including the quality of all equipment such as lubricating oil, fuel, accompanying tools, spare tires, etc. Maximum total mass (kg): the total mass when the car is fully loaded. Maximum loading mass (kg): the maximum loading mass when the car is driving on the road.
Therefore, the use of steel tape measure and gauge ruler can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and year of production should be correctly selected. ( 2) Parameter comparison: When comparing parameters, the following principles should generally be followed: ensure that the measurement reference point is not deformed.
1. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
2. You need a tape measure or laser rangefinder. If you choose to use a tape measure, make sure it is accurate and long enough to measure the length of the entire body. If you choose to use a laser rangefinder, follow the instructions to make sure that it has been calibrated and ready for use.
3. In order to accurately obtain the body data, the three steps are the measurement of the size, the measurement of the upper body size, and the measurement of the front size of the body. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. Measurement of the overall deformation of the car body: Body shaping positioning detection is to use the measurement system provided by the straightening system to measure the coordinate parameters of each measurement point on the body, and compare the measurement data with the standard data of the model to check the straightening quality.
5. Stop the car after driving 10km on the road with poor road conditions, and touch the shock absorber shell with your hand. If it is not hot enough, it means that there is no resistance inside the shock absorber and the shock absorber does not work.
The front bundle ruler can be used to check and measure the front bundle. The tested vehicle must ensure that the tire pressure, the wheel is not in the center, the steering mechanism and the wheel bearing adjustment are in good condition, and the front wheel must be in the center and straight. When measuring with a front ruler, park the car on a flat, dry and clean ground.
Measurement method of automobile front bundle: First of all, the measurement method of automobile wheel bearing clearance is adjusted, and the tire inflation pressure conforms to the regulations.
The adjustment and measurement of the front beam of the car are as follows: the front beam of the front wheel is to make the distance between the front end of the two front wheels of the car smaller than the distance of the rear end.The difference in distance is called the front beam value. Looking down from the top of the car, the left and right front wheels form an "eight" shape with an opening to the back; the front bundle of the front wheel can be adjusted by changing the length of the crossbar.
Checking the front bundle value is generally carried out on a special front wheel locator. The front beam measurement method is first of all to adjust the gap of the automobile wheel hub bearing, and the tire inflation pressure conforms to the regulations. Park the car on the horizontal road and drive in a straight line.
Therefore, when the current bundle value is inappropriate, it needs to be adjusted and measured. To measure the front beam of a car, it is generally necessary to use a special front wheel locator, and generally there is no such professional instrument for self-measurement, and it can only be measured through simple tools. Of course, there is a certain error in the front beam of the car measured in this way.
1. Car size detection is as follows: the body length is defined as the distance between the two extreme points of the car, that is, the distance between the two points from the most prominent position of the front bumper of the car to the most prominent position of the rear bumper.
2. Body size: First, we will measure the size of each part of the car body, including the length, width and height. These data are crucial to the design, manufacture and safety of vehicles. For example, if the body width exceeds the specified limit, the vehicle may not be able to drive on certain roads.
3. Measurement of size: In the body structure, most of the control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. When the freight vehicle passes through the off-site law enforcement monitoring point normally at a running speed range of 0.5-100km/h, the Shenbang outline size measurement ADM system can automatically complete the identification and measurement of the length, width and height profile size and wheelbase of the freight vehicle, and output the correct measurement results to Off-site law enforcement edge management server.
Global trade finance compliance checks
author: 2024-12-24 02:09How to utilize blockchain for trade
author: 2024-12-24 01:54Refined metals HS code references
author: 2024-12-24 01:43HS code mapping to product categories
author: 2024-12-24 01:19HS code-driven import quality checks
author: 2024-12-24 01:29HS code-based sourcing opportunities
author: 2024-12-24 00:30Advanced shipment lead time analysis
author: 2024-12-24 00:28Comparing international shipping carriers
author: 2024-12-24 00:10HS code-based SLA tracking for vendors
author: 2024-12-24 00:07
Customs data verification services
996.62MB
Check
HS code-driven letter of credit checks
193.88MB
Check
HS code intelligence for oil and gas industry
236.66MB
Check
HS code compliance for South American markets
431.94MB
Check
HS code-focused compliance audits
797.57MB
Check
HS code compliance for hazardous materials
721.96MB
Check
Global trade intelligence whitepapers
977.86MB
Check
Drilling equipment HS code mapping
886.25MB
Check
How to align sourcing strategy with trade data
392.46MB
Check
Enhanced due diligence via HS code
387.57MB
Check
HS code application in re-export scenarios
129.29MB
Check
Global trade partner compliance checks
483.15MB
Check
HS code intelligence in freight auditing
538.98MB
Check
Asia trade analytics platform
961.15MB
Check
Sourcing opportunities filtered by HS code
932.72MB
Check
HS code-driven market entry strategy
215.79MB
Check
HS code filters for bulk commodities
738.39MB
Check
USA importers database access
278.84MB
Check
Comparing international shipping carriers
295.99MB
Check
Asia trade corridors HS code mapping
321.14MB
Check
Germany export data by HS code
516.85MB
Check
Pharma finished goods HS code references
563.87MB
Check
How to use trade data for market expansion
757.11MB
Check
Heavy machinery parts HS code verification
649.34MB
Check
Trade data for market entry strategies
265.22MB
Check
Minimizing duties via HS code optimization
762.81MB
Check
Sustainable supply chain analytics
618.59MB
Check
Sourcing intelligence from customs data
584.93MB
Check
Real-time shipment inspection data
759.41MB
Check
Trade data-driven LCL/FCL strategies
863.38MB
Check
HS code harmonization in NAFTA region
748.26MB
Check
Refined sugar HS code identification
889.55MB
Check
Leveraging global trade statistics
735.68MB
Check
How to analyze trade seasonality
466.42MB
Check
HS code-driven portfolio diversification
573.71MB
Check
Processed nuts HS code references
418.57MB
Check
Scan to install
Medical reagents HS code verification to discover more
Netizen comments More
2097 International trade route optimization
2024-12-24 02:07 recommend
1054 Trade data for healthcare supplies
2024-12-24 02:02 recommend
1662 Composite materials HS code research
2024-12-24 00:51 recommend
1864 HS code-based transport cost modeling
2024-12-23 23:34 recommend
2092 Niche pharmaceuticals HS code verification
2024-12-23 23:34 recommend