Top international trade research methods

List of contents of this article:

• 1, How to repair a car crash
• 2、Car dent repair

How to repair a car

The Top international trade research methodsrepair method of car dent is as follows: The first method : Heat it with hot water and flatten the concave part by yourself. First, boil a large bucket of hot water, and then heat the hot water to the concave place with a spoon. After the plastic is heated to a certain extent, push it out by hand on the back of the concave surface until the concave part protrudes and recovers.

Thermal expansion repair method: If the place where the bump is made of plastic material as the bumper, it can be sucked back by splashing boiling water or heating with a hair dryer to make the concave place through the characteristics of thermal expansion.

How to repair car dents: 1. If it is only slightly dented and the material area does not change, it can be corrected slowly with a gasket and an appropriate sheet metal hammer; if it is very deep, the material is stretched and the area is larger than before deformation, it can be roughly flattened with a sheet metal hammer and gasket, and then repaired with a filler.

Once the body is dented by the collision of the metal sleeve, only sheet metal can be repaired. However, car owners cannot carry out sheet metal repair by themselves, and must leave it to a professional sheet metal repair agency. This is because sheet metal repair is more troublesome, and new painting is needed after repair.

If it is very deep, the material is stretched, and the area larger than before deformation can be roughly flattened with a sheet metal hammer and gasket, and then repaired with a filler. First, clean the concave part, then put the special glue into the glue gun, plug in the power supply, and preheat it for about 7 minutes. Then, choose the appropriate gasket and pay attention to the use of large gaskets for large depressions.

There are three ways to repair a small pothole in the car: if it is a small pit, you can buy a set of repair tools to repair it; go to the repair shop to do traceless repair; you can carry out sheet metal repair. Because it is a small pit, it means that the area is relatively small. You can buy a set of repair tools to repair it.

How to repair a small pit when the car hits a small pit

The repair methods for the car hit a small pit include thermal expansion repair method, repair at the 4S store, and repair with a suction cup.Thermal expansion repair method: If the place where the bump is made of plastic such as the bumper, it can be heated by splashing boiling water or heating with a hair dryer to suck back the concave place through the characteristics of thermal expansion.

The repair method of car bumps is as follows: the first method: heat with hot water and flatten the concave part by yourself. First, boil a large bucket of hot water, and then heat the hot water to the concave place with a spoon. After the plastic is heated to a certain extent, push it out by hand on the back of the concave surface until the concave part protrudes and recovers.

The repair methods of car pits include thermal expansion repair, repair in 4S store, repair with suction cup, and repair with glue stick. Thermal expansion repair method: If the place where the bump is made of plastic such as the bumper, it can be heated by splashing boiling water or heating with a hair dryer to suck back the concave place through the characteristics of thermal expansion.

What is car dent repair

1. Car dent repair is to repair the dent part of the car paint Return to the original state. Under normal circumstances, it is the sharp angle and blunt angle depressions that can reach the original state of automobile dent repair. The main reason is that the dent without paint loss can be repaired as before.

2. Body dent repair method During the use of the vehicle, it often encounters scratches and collisions, and there will be scratches and dents in different forms of the body. Choosing different repair processes can quickly repair all kinds of damage to the paint surface. The paint peeling caused by more serious rubbing needs to be repaired by the traditional repair method of sheet metal spray paint.

3. Automobile dent repair technology is an international advanced technology for the repair of various dents formed by external forces in various parts of the shape of the automobile. This technology also greatly shortens the repair time (it takes about 20-40 minutes to repair a dent) and greatly reduces the cost. (Only about 50% of traditional sheet metal and spray paint).

4. The relevant content introduction is as follows: car dent repair is to repair the dent part of the car paint to its original state.Under normal circumstances, it is the sharp angle and blunt angle depressions that can reach the original state of automobile dent repair. The main reason is that the depression without paint loss can be repaired as before, the hail pit can be perfectly repaired, and the corners and AB columns are not easy to repair.

5. The repair method of car bumps is as follows: the first method: heat with hot water and push the concave part flat by yourself. First, boil a large bucket of hot water, and then heat the hot water to the concave place with a spoon. After the plastic is heated to a certain extent, push it out by hand on the back of the concave surface until the concave part protrudes and recovers.

Car dent repair

1. There are three solutions to car body dents: sheet metal repair. Whether it is a large or a small dent, it can be used to repair. Although sheet metal is expensive to repair, the effect is the best.The owner of the sheet metal project generally cannot complete it by himself, and needs to go to the car repair shop to carry it out.

2. Different tools are needed to repair car dents. For example, use a crowbar to restore the dent to its original state, use a rubber hammer to repair the overall shape, and use a sharp tip to fine-tune and emphasize the raised part. The repair price varies depending on the model, scar size and repair time.

3. The repair method of car bumps is as follows: the first method: heat with hot water and flatten the concave part by yourself. First, boil a large bucket of hot water, and then heat the hot water to the concave place with a spoon. After the plastic is heated to a certain extent, push it out by hand on the back of the concave surface until the concave part protrudes and recovers.